Inside EdgeDented panels
- Part
- Sections (panels)
- Usual time on site
- About 2 hours, once the matching section is in
- Permit
- We tell you before we start
- Call or text
- (954) 947-4016
Garage door panel replacement that keeps your rating
Garage door panel replacement means swapping only the damaged section for a new one of the same model, size and finish, while every other section stays put. In Pembroke Pines there's one more check: on an impact-rated door, the new section has to belong to the same product approval as the door. So the label gets read before anything else.
When a section is the problem
- Someone backed into it, and the bottom section is pushed in or creased.
- There's a crack following the seam where two sections meet.
- A hinge pulled loose, and the metal around its screws is torn.
- Each trip, the door scrapes or snags at one spot, right where the bent section meets the track.
- The lowest section has rusted along the edge that meets the floor.
- That bump also pushed rollers out of the rails? Read cable and track repair. Door won't close tonight? Call for emergency repair.
Sections (panels)
A sectional door is a stack of horizontal sections joined by hinges, each with its own rollers. On an impact door, steel struts run across the sections, and the inside edge of one section carries a label naming the product approval. In the loop, the sections glow one by one, from the bottom section, which takes most of the bumps, up to the one under the header.
The label decides what can be ordered
Look inside the door, typically along the edge of one section: a label lists who made the door, the model and its size. Impact-rated doors add the design pressure and an approval number, Florida Product Approval (FL) or Miami-Dade NOA. We photograph that label before ordering a thing. If the maker still builds that model, the section comes matched in model, width and finish. If not, you find out on the first visit.
Impact doors: stay inside the approval
An impact door's approval describes the door as it was tested: sections, struts, hinges and anchors. Fit a section from another model, or a generic one that merely looks alike, and you may end up with a door nobody can prove is rated. That's why the approval gets checked before ordering, and only a section that belongs to it goes on. For help finding and reading your own label, see reading your door's approval label.
Not every product sold as "Florida approved" is approved for the High-Velocity Hurricane Zone (HVHZ); the approval document itself says which. When an entire door is replaced, the city's permit checklist asks for that product approval (City of Pembroke Pines checklist).
Dents, rust and HOA colors
A small dent that never touches the track can often stay. Rust along the bottom edge shows up where water sits against the slab, and how deep it goes decides whether that section can be saved. Where an HOA dictates door colors, we order in the door's own finish; a section from a newer production run can read slightly different in strong sun, and you'll hear that before ordering. Not sure the section is the issue? Try the troubleshooting guide.
What changes the job
- Is the model still in production?
- A current model means a matching section. A discontinued one may mean living with the dent or replacing the door, and you know which before anything is ordered.
- Impact rating
- On an impact door, the section has to come from the same approval, often with its own strut. That narrows what can be ordered.
- Which section
- The lowest section carries the cable brackets and the floor seal, so swapping it means releasing spring tension first. A middle section means more hinges and rollers to move.
- Windows and insulation
- A section with glass or foam has to match those too, or the door won't look the same or weigh the same, and the springs are set for its weight.
Swapping one section is work on the existing door; frame and opening stay untouched. Repairs that don't touch the frame or the opening usually don't change the permit picture; when one does, we tell you before we start. A whole new door, on the other hand, needs a city permit: details in our Pembroke Pines permit guide.
Questions about this
Is replacing a single garage door panel possible?
Yes, if the maker still produces your door's model and the remaining sections are sound. We order the new section to the model, size and finish on the door's label.
Does replacing a panel affect my door's hurricane rating?
It can. On an impact-rated door, the new section has to belong to the same product approval as the door, so we check the approval before ordering. A section from outside it may leave the door unable to show its rating.
Should I replace a panel or the whole door?
Replace the panel when the model is available and the remaining sections look sound. Replacing the whole door makes sense once the model is discontinued, more than one section is damaged, or there's no approval you can verify; see new garage doors.
Where is the label on my garage door?
Usually along the edge of one of the sections, facing into the garage. It shows who made the door and which model it is; impact doors add the design pressure and an approval number.
Call, or text us a photo first
A person answers 24/7. If it isn't urgent, a photo of the sections (panels) helps us bring the right part.